By Josephine Smith

A Material Buildup Problem in a Cyclone Was Solved Using Air Cannons to Return Normal Flow to the System and Prevent Future Blockages.

One of the largest producers in Turkey, the Büyükçekmece cement plant operated by Akçansa Group – a joint venture between Sabanci Holding and Heidelberg Cement – supplies 10 percent of the country’s total demand and 12.5 percent of the total cement and clinker exports.

Originally built in 1967, the facility has three clinker production kilns with a capacity of 5,900 tpd. It’s also considered the pioneer in alternative fuel use in Turkey’s cement industry with a current fuel ratio of 77 percent pet coke and 23 percent alternative fuels.

Accumulation Issue
As the facility’s output capacity increased and fuel types changed over the years, workers began having to manually dislodge material buildup in Cyclone 4 of Kiln #2’s preheater tower in order to maintain throughput. The unscheduled shutdowns to allow cleanout of the cone and deep tube interfered with production schedules and exposed maintenance staff to potential hazards.

In addition to the necessary cooling time, the cyclone cleanout process required 3-4 people working with jackhammers through access doors for several hours. Unfortunately, even after expending all that time and energy, the accumulation became so severe that the problem would typically return within a week, choking off the material flow and forcing yet another shutdown. Plant officials contacted Martin Engineering Turkey to conduct an audit of the process, and a joint effort was developed to determine the optimum solution.

A Proven Approach
Upon completion of the audit, it was determined that a series of air cannons would be the best option to return normal flow to the system and prevent future blockages. The timed discharge of a directed air blast can prevent accumulation that impacts process efficiency and raises maintenance expenses, while helping manufacturers to minimize the need for process interruptions and manual labor.

Engineers from the two companies met to discuss details, including air cannon design, nozzle selection and specific locations to maintain optimum material flow. To control the material buildups and maintain production stability, 29 Big Blaster Hurricane Air Cannons were supplied by Martin Engineering Turkey, each with a 70-liter reservoir, installed in strategic locations by a Martin Service Team.

The installation included hi-velocity and fan-jet nozzles with Martin Thermo Safety Shields to protect maintenance personnel when they inspect or service the air cannon system. Also known as blast guards, Thermo Safety Shields are situated between the process and the air cannon valve itself. Available in manual or air-operated models, these devices help prevent material backflow during service and shield the air cannon valve components from material spray.

The new air cannons were arranged in three groups, each directed by the plant’s control room. The discharge sequence moves upward in a spiral, with cannons firing 10 seconds apart. The entire 80-90 second cycle typically repeats approximately every 20 minutes, but operators have varied the time from 5-45 minutes, depending on specific operating conditions.

Since the installation of the new air cannon network, no unscheduled shutdowns have been caused by material buildup in that section of the cyclone. With the problem solved, engineers have turned their attention to some additional buildups higher in the deep tube, an area not covered by the air cannon network. During its next shutdown, the plant will install an additional set of four 70L Hurricane Air Cannons, locating them above the cyclone deep tube.

Cost Reduction
The audit also revealed an opportunity to reduce the operating cost of the facility’s 22 existing Tornado Air Cannons at the inlet chamber and riser duct of the Kiln #2 preheater tower by upgrading each one with a Martin Piston Return Reservoir, a canister that closes the valve after approximately 50 percent of the volume has been discharged. The reservoir is a pneumatic device that collects the exhaust air from the valve and redirects that pressure to close the piston when the valve and tank pressure equalize.

When equipped with a piston return reservoir, the air cannon produces an initial blast force of the same strength, but the duration of the discharge is reduced. Instead, the air retained inside the cannon’s tank minimizes the overall air consumption without reducing initial output force. Since the main air tank is never completely evacuated, the volume of air required to refill after each discharge is reduced. With the air cannon’s peak force unaffected, the same amount of work can be accomplished with half the amount of compressed air.

Before the installation of the return reservoirs, the air consumption of the 22 Tornado Air Cannons at Büyükçekmece was estimated at 2 cu. m/minute, or an annual total air consumption of approximately 525,600 cu. m. If the cost of service air is estimated at two cents per cubic meter, the total air cost would be $10,512 per year.

After installation of the reservoirs, the annual air consumption has been reduced to 262,800 cu. m, while retaining the same air cannon performance. If the minimum lifetime of an air cannon is estimated at 10 years (not an unreasonable prospect), the cost savings over that period would be $52,560.

Information courtesy of Martin Engineering, www.martin-eng.com 

 

2017 Cement Directory

NACD
 

Completely updated, the new 2017 North American Cement Directory. Currently available for ordering exclusively from Cement Americas. Order Now

Resource Center

Let's stay in touch!

All of the latest news and our digital edition sent to your inbox once a week.

We'll never share your email address, and you can opt out at any time, we promise.